Been a busy week so far, but had a chance to take a closer look at the innards of the monitor tonight, particularly the steel casing.
There was a glimmer of hope when I noticed the tabletop was a little wider than the unit overall, which would just about let the screen fit centrally with some careful use of the router. Problem is, the monitor is thicker than the tabletop, so there would need to be a little wood cut from the side of the unit, which would look terrible.
So, off out to the garage for some experimentation - it looks like some very careful sawing could remove the section around the control panel, allowing for an easy central fit on the tabletop. Not doing it tonight though, going to get a few nice fine-toothed blades for my saw first.
Showing posts with label joe teach. Show all posts
Showing posts with label joe teach. Show all posts
Tuesday, 13 April 2010
Saturday, 10 April 2010
Not going to be easy...
Well, in my infinite wisdom I decided to put a bit more time into this project late on a Saturday night after a few bottles of cider. All things considered I've come out of it relatively unscathed.
First things first, as this is such a nice monitor I wanted to see if I could get away with keeping it in its original casing, but a quick check on top of the unit after removing the stand showed it was just too big:

It was then that I somewhat rashly decided to set about removing the casing, to see if there was any way of minimising the width...
A few tense minutes later and we have this (excuse the blurry photo!):

Unfortunately the shielding extends all the way to the bottom of the monitor where the control PCB is:

Managed to fiddle around removing screws and a very tricky ribbon cable to get the PCB out of the way and get a better look at the offending piece of metal:

I thought about using a router to remove some of the inside of the IKEA unit to allow it to fit, but I would need to remove 17mm, which is about the thickness of the wood so that's a no. My other options are to cut away the piece entirely, which is going to be tricky without damaging the TFT, or bending it, which is also going to require some cuts. That's going to have to be a more sober decision I think.
What I did do, however, was to hook up the monitor for a little testing, albeit off to one side in the cab. I removed the top of the unit and hooked up the panel to my netbook, plugged it in and lay it flat on top of the closed drawer. Got MAME up and running and all looks good:


Then, I opened up the smoked glass panel and laid it over the top, looked fantastic with Pac Man running in it, shame I couldn't have the drawer open for my stick to rest on, would probably still be playing now!


After I packed everything away, tried out the glass panel on top of the unit, it looks pretty good but the white shows up a lot. When the unit is all done I'll need a layer of black paper with a bezel cut out so the screen blends in a bit more when not in use.

So, an eventful evening. I think I needed to be a little drunk to have the confidence to start pulling such a great little monitor apart. Well, more a great big monitor really.
First things first, as this is such a nice monitor I wanted to see if I could get away with keeping it in its original casing, but a quick check on top of the unit after removing the stand showed it was just too big:
It was then that I somewhat rashly decided to set about removing the casing, to see if there was any way of minimising the width...
A few tense minutes later and we have this (excuse the blurry photo!):
Unfortunately the shielding extends all the way to the bottom of the monitor where the control PCB is:
Managed to fiddle around removing screws and a very tricky ribbon cable to get the PCB out of the way and get a better look at the offending piece of metal:
I thought about using a router to remove some of the inside of the IKEA unit to allow it to fit, but I would need to remove 17mm, which is about the thickness of the wood so that's a no. My other options are to cut away the piece entirely, which is going to be tricky without damaging the TFT, or bending it, which is also going to require some cuts. That's going to have to be a more sober decision I think.
What I did do, however, was to hook up the monitor for a little testing, albeit off to one side in the cab. I removed the top of the unit and hooked up the panel to my netbook, plugged it in and lay it flat on top of the closed drawer. Got MAME up and running and all looks good:
Then, I opened up the smoked glass panel and laid it over the top, looked fantastic with Pac Man running in it, shame I couldn't have the drawer open for my stick to rest on, would probably still be playing now!
After I packed everything away, tried out the glass panel on top of the unit, it looks pretty good but the white shows up a lot. When the unit is all done I'll need a layer of black paper with a bezel cut out so the screen blends in a bit more when not in use.
So, an eventful evening. I think I needed to be a little drunk to have the confidence to start pulling such a great little monitor apart. Well, more a great big monitor really.
Monday, 5 April 2010
Introduction.
I love playing on arcade machines. The joy of playing a game via a big chunky joystick, especially on a vertically oriented screen, has a big appeal for me.
Having built a Dreamcast powered cocktail arcade cab in the past, and owned a Neo Geo upright cab, these have all had to go in favour of a more sensible home environment to make space for our two kids.
A recent hankering for a new cab brought out some interesting discussion with friends regarding the construction of a new cocktail cab. A modular approach emerged, resulting in a unit that could be packed away or remain a little less obvious when not in use. I looked at IKEA for some simple inspiration, and ended up deciding I may as well use one of their units as a starting point rather than build my own cab from scratch.
Skipping ahead, I've done some further research and decided on a 2-drawer unit called MALM to act as the bare bones for my cab. The plan is that the unit doesn't resemble an arcade cab at all, hence the "stealth" in the title. Until the joystick is revealed and the monitor fires up, it's just going to look like a normal piece of furniture.
The cab is going to be designed pretty much exclusively for vertically oriented or "tated" games, partly due to the shape of the unit I've chosen and partly due to the suitable viewing angles of the monitor I'm using. Also, I can always play standard orientation games via my TV.
Pictures to follow when I get the chance, hope this will be of interest to some people.
Having built a Dreamcast powered cocktail arcade cab in the past, and owned a Neo Geo upright cab, these have all had to go in favour of a more sensible home environment to make space for our two kids.
A recent hankering for a new cab brought out some interesting discussion with friends regarding the construction of a new cocktail cab. A modular approach emerged, resulting in a unit that could be packed away or remain a little less obvious when not in use. I looked at IKEA for some simple inspiration, and ended up deciding I may as well use one of their units as a starting point rather than build my own cab from scratch.
Skipping ahead, I've done some further research and decided on a 2-drawer unit called MALM to act as the bare bones for my cab. The plan is that the unit doesn't resemble an arcade cab at all, hence the "stealth" in the title. Until the joystick is revealed and the monitor fires up, it's just going to look like a normal piece of furniture.
The cab is going to be designed pretty much exclusively for vertically oriented or "tated" games, partly due to the shape of the unit I've chosen and partly due to the suitable viewing angles of the monitor I'm using. Also, I can always play standard orientation games via my TV.
Pictures to follow when I get the chance, hope this will be of interest to some people.
Subscribe to:
Posts (Atom)